• CBLR2-HD: Side, Vertical Orientation
  • CBLR2-HD: Side, Horizontal Orientation
  • FT-TS600 w/CBLR2, Vertical, Front View
  • FT-TS600 w/CBLR2, Horizontal, Front View
  • FT-TS600 w/CBLR2, Compartment View

Cable Retractors for FlipTops™

CBLR2

Provides a retractable cable management solution for Crestron FlipTops™

More Details


Crestron® Cable Retractors offer a refined cable management solution for use with Crestron FlipTops™. Using cable retractors, anyone can simply reach into the FlipTop™ storage compartment and pull out the appropriate cable to connect their device. Each cable pulls out smoothly to a length of 3 feet (0.9 meter) and latches in position. A second pull of the cable releases the latch and retracts the cable back into the compartment.

Each Crestron Cable Retractor features a patented mechanism that dampens the rate of retraction to prevent the cable from whipping as it’s pulled back into the FlipTop storage compartment. The retraction speed is installer adjustable to ensure full and effortless retraction without excessive force.

Up to three, four, or six cable retractors can be installed depending on the FlipTop model (see specifications for quantity and compatibility). Spacer inserts are available to fill any unused cable retractor spaces.[1]

Cable retractors can be oriented in two possible positions. In their default vertical position, the retractors hang straight down from the bottom of the FlipTop box allowing them to be hidden in a pedestal leg or similar space directly beneath the FlipTop. When positioned horizontally, the retractors project to the sides or front of the FlipTop, eliminating any obstruction near the floor.[2]

A 7 foot (2.1 meter) long tail is provided at the back-end of each cable retractor beneath the tabletop. This tail can be plugged into a wall plate or floor box, or connected to a DigitalMedia™ transmitter or similar interface device mounted under the table.

Several models of cable retractors are currently offered to support HDMI® [3], DisplayPort [2], VGA, stereo audio, USB, and CAT5e connectivity. The CAT5e model is suitable for Ethernet, HDBaseT®, and DigitalMedia 8G+® applications.

Please see Note #4 for information regarding compatibility with 1st generation CBLR Cable Retractors.[4]

To configure a complete 600 Series FlipTop with your choice of finishes, cables, cable retractors, connector plates, and power outlets, please use the online Crestron FlipTops Configuration Tool.

Notes

  1. When installing fewer than the maximum quantity of cable retractors, a spacer insert is required to fill each unused cable retractor space. For FlipTop 600 Series, use the FTA-CBLRA-INSERT-2WIRE-102. For all other FlipTops, use the CBLRA-INSERT-2WIRE or CBLRA-INSERT-BLANK. All spacer inserts are sold separately.
  2. All CBLR2 Series cable retractors are field-configurable for vertical or horizontal orientation except for the CBLR2-DP-V and CBLR2-DP-H, which are preconfigured and cannot be converted. When installed horizontally, the retractors project to the left and/or right sides of a FlipTop 600 Series unit and to the front of any other model FlipTop.
  3. The CBLR2-HD model features active electronics and is designed for use as an input only. The source device must be connected to the pull-out end, and the sink device (e.g., the input of a display, monitor, transmitter, switcher, etc.) must be connected to the back end (labeled “TV” on the connector). The CBLR2-HD has a minimum TMDS bandwidth of 10.2 Gbps and is capable of passing video signals up to 4K60 4:2:0 and 4K30 4:4:4 maximum.
  4. CBLR2 series cable retractors may be installed in place of, or in combination with, existing 1st generation CBLR series cable retractors, bearing in mind the following factors: A) Combining CBLR and CBLR2 series retractors within a single FlipTop housing may complicate end-user operation due to the differences in their latching and retraction mechanisms. B) For vertical installation, the CBLR2 series requires approximately 2 inches (50 mm) more vertical clearance below the mounting surface than the CBLR series. C) For horizontal installation, the CBLR2 series requires approximately 1.5 inches (38 mm) more horizontal clearance than the CBLR series. Please note the additional knee clearance that may be required in some instances. D) For horizontal installations combining CBLR2 retractors alongside existing CBLR retractors, it may be necessary to reposition the existing CBLRA-BRKT-H bracket. This bracket must be retained to support the existing CBLR retractors, but should be offset to one side to allow clearance for the new CBLR2 retractors, which do not utilize the bracket themselves.
  5. Item(s) sold separately.

This product may be purchased from an authorized Crestron dealer. To find a dealer, please contact the Crestron sales representative for your area. A list of sales representatives is available online at www.crestron.com/salesreps or by calling 800-237-2041.

The specific patents that cover Crestron products are listed online at: patents.crestron.com.

Certain Crestron products contain open source software. For specific information, please visit www.crestron.com/opensource.

Crestron, the Crestron logo, DigitalMedia, DigitalMedia 8G+, FlipTop, FlipTops, and QuickMedia are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries. HDBaseT is either a trademark or registered trademark of the HDBaseT Alliance in the United States and/or other countries. HDMI is either a trademark or registered trademark of HDMI Licensing LLC in the United States and/or other countries. Other trademarks, registered trademarks, and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not responsible for errors in typography or photography. Specifications are subject to change without notice. ©2017 Crestron Electronics, Inc.

  • Easy-to-use — pull out the cable to its full length (3 ft / 0.9 m) to latch, pull it again to retract
  • Eliminates hanging cable loops beneath the table
  • Keeps interface cables at-the-ready
  • No levers or buttons to press
  • Patented mechanism prevents whipping of the cable while retracting
  • Provides a refined cable management solution for Crestron FlipTops™
  • Vertical and horizontal mounting options accommodate most tabletop applications
  • Models available to support HDMI® [3], DisplayPort [2], VGA, stereo audio, USB, Ethernet, HDBaseT®, and DigitalMedia 8G+®

Notes

  1. When installing fewer than the maximum quantity of cable retractors, a spacer insert is required to fill each unused cable retractor space. For FlipTop 600 Series, use the FTA-CBLRA-INSERT-2WIRE-102. For all other FlipTops, use the CBLRA-INSERT-2WIRE or CBLRA-INSERT-BLANK. All spacer inserts are sold separately.
  2. All CBLR2 Series cable retractors are field-configurable for vertical or horizontal orientation except for the CBLR2-DP-V and CBLR2-DP-H, which are preconfigured and cannot be converted. When installed horizontally, the retractors project to the left and/or right sides of a FlipTop 600 Series unit and to the front of any other model FlipTop.
  3. The CBLR2-HD model features active electronics and is designed for use as an input only. The source device must be connected to the pull-out end, and the sink device (e.g., the input of a display, monitor, transmitter, switcher, etc.) must be connected to the back end (labeled “TV” on the connector). The CBLR2-HD has a minimum TMDS bandwidth of 10.2 Gbps and is capable of passing video signals up to 4K60 4:2:0 and 4K30 4:4:4 maximum.
  4. CBLR2 series cable retractors may be installed in place of, or in combination with, existing 1st generation CBLR series cable retractors, bearing in mind the following factors: A) Combining CBLR and CBLR2 series retractors within a single FlipTop housing may complicate end-user operation due to the differences in their latching and retraction mechanisms. B) For vertical installation, the CBLR2 series requires approximately 2 inches (50 mm) more vertical clearance below the mounting surface than the CBLR series. C) For horizontal installation, the CBLR2 series requires approximately 1.5 inches (38 mm) more horizontal clearance than the CBLR series. Please note the additional knee clearance that may be required in some instances. D) For horizontal installations combining CBLR2 retractors alongside existing CBLR retractors, it may be necessary to reposition the existing CBLRA-BRKT-H bracket. This bracket must be retained to support the existing CBLR retractors, but should be offset to one side to allow clearance for the new CBLR2 retractors, which do not utilize the bracket themselves.
  5. Item(s) sold separately.

This product may be purchased from an authorized Crestron dealer. To find a dealer, please contact the Crestron sales representative for your area. A list of sales representatives is available online at www.crestron.com/salesreps or by calling 800-237-2041.

The specific patents that cover Crestron products are listed online at: patents.crestron.com.

Certain Crestron products contain open source software. For specific information, please visit www.crestron.com/opensource.

Crestron, the Crestron logo, DigitalMedia, DigitalMedia 8G+, FlipTop, FlipTops, and QuickMedia are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries. HDBaseT is either a trademark or registered trademark of the HDBaseT Alliance in the United States and/or other countries. HDMI is either a trademark or registered trademark of HDMI Licensing LLC in the United States and/or other countries. Other trademarks, registered trademarks, and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not responsible for errors in typography or photography. Specifications are subject to change without notice. ©2017 Crestron Electronics, Inc.

CAT5e
(T-568B straight-through, unshielded)
DisplayPort [2]
HDMI® [3]
Stereo Audio
(Unbalanced)
USB
VGA
VGA + Stereo Audio (Unbalanced)
Mounted horizontally to both sides of a FlipTop 600 Series, including FlipTop Box with lid closed and all required mounting brackets:
Mounted horizontally using CBLRA-BRKT-3-FT, including FlipTop Box with lid closed and all required mounting brackets:
Mounted horizontally using CBLRA-BRKT-4-FT, including FlipTop Box with lid closed and all required mounting brackets:
Mounted horizontally using CBLRAI-BRKT-4-FT, including FlipTop Box with lid closed and all required mounting brackets:
Mounted vertically to both sides of a FlipTop 600 Series, including FlipTop Box with lid closed and all required mounting brackets:
Mounted vertically using CBLRA-BRKT-3-FT, including FlipTop Box with lid closed and all required mounting brackets:
Mounted vertically using CBLRA-BRKT-4-FT, including FlipTop Box with lid closed and all required mounting brackets:
Mounted vertically using CBLRAI-BRKT-4-FT, including FlipTop Box with lid closed and all required mounting brackets:
Depth 23.04 in (586 mm)
Depth 23.61 in (600 mm)
Depth 23.68 in (602 mm)
Depth 4.00 in (102 mm)
Depth 6.77 in (172 mm)
Depth 7.74 in (197 mm)
Depth 8.34 in (212 mm)
Depth 8.40 in (214 mm)
Height 22.44 in (570 mm)
Height 25.00 in (635 mm)
Height 25.14 in (639 mm)
Height 25.29 in (643 mm)
Height 25.32 in (644 mm)
Height 9.27 in (236 mm)
Height 9.42 in (240 mm)
Height 9.48 in (241 mm)
Height 9.60 in (244 mm)
Width 1.12 in (29 mm)
Width 10.16 in (258 mm)
Width 42.03 in (1068 mm)
Width 6.75 in (172 mm)
Width 7.67 in (195 mm)
Width 8.50 in (216 mm)
Metal, black
Humidity 10% to 90% RH (non-condensing)
Temperature 41° to 104°F (5° to 40°C)
C2N-FT-TPS4
C2N-FT-TPS4-U
FT-PWR-D-LG
QM-FTCC-TPS4
C2N-FTB-D
FT-PWR-D
QM-FTCC
QM-FTCC-NB
QM-FTDC
QM-FTDC-NB
QM-FTMC
QM-FTMC-NB
QM-FTMCSC
QM-FTMCSC-NB
FT-600
FT-TS600
FT-TSC600
FT-600
FT-TS600
FT-TSC600
FTI-PWR-D
QMI-FTCC
QMI-FTDC
QMI-FTMC
QMI-FTMCSC
IM-FTCC-M
IM-FTCCV-M
IMI-FTCC-M
IMI-FTCCV-M
QMI-FTCC-TPS4
2.14 lb (970 g) each

Notes

  1. When installing fewer than the maximum quantity of cable retractors, a spacer insert is required to fill each unused cable retractor space. For FlipTop 600 Series, use the FTA-CBLRA-INSERT-2WIRE-102. For all other FlipTops, use the CBLRA-INSERT-2WIRE or CBLRA-INSERT-BLANK. All spacer inserts are sold separately.
  2. All CBLR2 Series cable retractors are field-configurable for vertical or horizontal orientation except for the CBLR2-DP-V and CBLR2-DP-H, which are preconfigured and cannot be converted. When installed horizontally, the retractors project to the left and/or right sides of a FlipTop 600 Series unit and to the front of any other model FlipTop.
  3. The CBLR2-HD model features active electronics and is designed for use as an input only. The source device must be connected to the pull-out end, and the sink device (e.g., the input of a display, monitor, transmitter, switcher, etc.) must be connected to the back end (labeled “TV” on the connector). The CBLR2-HD has a minimum TMDS bandwidth of 10.2 Gbps and is capable of passing video signals up to 4K60 4:2:0 and 4K30 4:4:4 maximum.
  4. CBLR2 series cable retractors may be installed in place of, or in combination with, existing 1st generation CBLR series cable retractors, bearing in mind the following factors: A) Combining CBLR and CBLR2 series retractors within a single FlipTop housing may complicate end-user operation due to the differences in their latching and retraction mechanisms. B) For vertical installation, the CBLR2 series requires approximately 2 inches (50 mm) more vertical clearance below the mounting surface than the CBLR series. C) For horizontal installation, the CBLR2 series requires approximately 1.5 inches (38 mm) more horizontal clearance than the CBLR series. Please note the additional knee clearance that may be required in some instances. D) For horizontal installations combining CBLR2 retractors alongside existing CBLR retractors, it may be necessary to reposition the existing CBLRA-BRKT-H bracket. This bracket must be retained to support the existing CBLR retractors, but should be offset to one side to allow clearance for the new CBLR2 retractors, which do not utilize the bracket themselves.
  5. Item(s) sold separately.

This product may be purchased from an authorized Crestron dealer. To find a dealer, please contact the Crestron sales representative for your area. A list of sales representatives is available online at www.crestron.com/salesreps or by calling 800-237-2041.

The specific patents that cover Crestron products are listed online at: patents.crestron.com.

Certain Crestron products contain open source software. For specific information, please visit www.crestron.com/opensource.

Crestron, the Crestron logo, DigitalMedia, DigitalMedia 8G+, FlipTop, FlipTops, and QuickMedia are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries. HDBaseT is either a trademark or registered trademark of the HDBaseT Alliance in the United States and/or other countries. HDMI is either a trademark or registered trademark of HDMI Licensing LLC in the United States and/or other countries. Other trademarks, registered trademarks, and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not responsible for errors in typography or photography. Specifications are subject to change without notice. ©2017 Crestron Electronics, Inc.

Available Models
Available Accessories